Hi yayan. 

Thank you for your reply. 

Sorry for ask but I just have few more questions:

sel4-tools
  • the elfloader-tool that is used to loads the arm kernel seams a  bit confused for me. I suppose that it just generate a .elf file representing the kernel  it is right?
  •  I don't think they are related. But In which way the  elfloader-tool interacts with U-boot?
  • The sel4-tools/ CMakeList.txt :165 has  a line "if (ElfloaderImageEFI) ". I'm not sure if it is supported by the U-boot within the rensas H3ULCB board. In case  that not. what I should do ?
GIC:
The renesas H3ULCB  has a GIC-400 unit and seams it is no supported by SeL4. may I wrong? 
  • if it is not supported, I should implemented in  order  to make Sel4 works in this board?
  • how it is used by the seL4 kernel? 
you can check up my work here: https://github.com/Daparrag/seL4/tree/rcar_h3sel4

thank you.

On Mon, 18 Feb 2019 at 23:48, <Yanyan.Shen@data61.csiro.au> wrote:

Hi Diego,


core_entry_head and init_cpus are for bringing up secondary cores. If you want to utilise more than one core, you need to implement the functions. I am not sure about your board, but PSCI (power state coordination interface) is usually used to bring up secondary cores. Please have a look at the TX1 plat. Your SoC manual should also explain how to bring up secondary cores.


The elfloader assumes the the uart port for printf is initialised by the uboot or other boot loaders. Otherwise, the elfloader needs to set up the port.


Hope this can help a bit.



Regards,

Yanyan


From: Devel <devel-bounces@sel4.systems> on behalf of Diego Alejandro Parra Guzman <daparrag@correo.udistrital.edu.co>
Sent: Monday, February 18, 2019 6:11 PM
To: devel@sel4.systems
Subject: Re: [seL4] port SeL4 to renesas rcar-H3 development board
 
Hi guys !!! 

Thank you for your quick replay.

I'm try to port Sel4 kernel to the renesas H3 ULCB board with two clusters (ARM57),(ARM53) each one with 4 cores  

I just have couple of questions regarding with  the elf loader in sel4-tools:

there is  some files in elfloader-tool/plat/* those are intended to initialize the CPU and the UART on the platform. In there, there is a function written in assembly called  core_entry_head  and a function init_cpusimplemented in smp.c file.
Could you please explain me  a  little bit what is the purpose of these functions ? 

In the case of init_cpus where is suppose to be that information? I means, I should  reference the ARM57 or ARM53 cpu manual or maybe to the boot section in the SoC manual.


from the other hand the renesas H3 ULCB doesn't have a physical UART port. Instead, it has an Serial Communication Interface with FIFO (SCIF) that can be configure properly to be compatible with UART interfaces. The point is that  I'm using this interface in order to implement the __fputc()  function following the one implemented in sys_fput.c file.  Unfortunately,  I don't understand why in your implementation there is not an initialization for the UART.  could you tell me why not?

Thank you.     

best regards

On Sat, 16 Feb 2019 at 06:57, Diego Alejandro Parra Guzman <daparrag@correo.udistrital.edu.co> wrote:
Hi guys !!! 

Thank you for your quick replay.

I'm try to port Sel4 kernel to the renesas H3 ULCB board with two clusters (ARM57),(ARM53) each one with 4 cores  

I just have couple of questions regarding with  the elf loader in sel4-tools:

there is  some files in elfloader-tool/plat/* those are intended to initialize the CPU and the UART on the platform. In there, there is a function written in assembly called  core_entry_head  and a function init_cpusimplemented in smp.c file.
Could you please explain me  a  little bit what is the purpose of these functions ? 

In the case of init_cpus where is suppose to be that information? I means, I should  reference the ARM57 or ARM53 cpu manual or maybe to the boot section in the SoC manual.


from the other hand the renesas H3 ULCB doesn't have a physical UART port. Instead, it has an Serial Communication Interface with FIFO (SCIF) that can be configure properly to be compatible with UART interfaces. The point is that  I'm using this interface in order to implement the __fputc()  function following the one implemented in sys_fput.c file.  Unfortunately,  I don't understand why in your implementation there is not an initialization for the UART.  could you tell me why not?

Thank you.     

best regards

On Wed, 13 Feb 2019 at 15:21, Diego Alejandro Parra Guzman <daparrag@correo.udistrital.edu.co> wrote:

Hi,

I'm new with seL4 kernel and I would like to port it to the ARM-based renesas rcar-H3 board

I would like to ask of you have a development manual that i can follow with some basics about how to do it?

I followed the tutorials and so one. But  I will appreciate if you have something guidelines to start. 

Thank you

BR
Diego.
--
Diego Alejandro Parra Guzmán
Estudiante de ingeniería electrónica
Universidad distrital FJC


--
Diego Alejandro Parra Guzmán
Estudiante de ingeniería electrónica
Universidad distrital FJC


--
Diego Alejandro Parra Guzmán
Estudiante de ingeniería electrónica
Universidad distrital FJC


--
Diego Alejandro Parra Guzmán
Estudiante de ingeniería electrónica
Universidad distrital FJC