Hi Michal,

It is strange that there is no further output, although I am worried about the IOMMU faults that happen just prior to that. On some systems certain devices (notably USB controllers) can lock parts of the system if they are unable to function correctly. My suggestion would be to resolve those IOMMU faults first.

If I had to guess the IOMMU faults you are seeing at the end of log are from the USB controller. Typically most boot loaders that load off USB leave the controllers active after performing the boot, whilst seL4 assumes that all devices are inactive such that it can safely enable the IOMMUs.

My suggestion therefore is try and boot your image from the flash storage or over the network via PXE and see if that resolves the faults.

Adrian

On 21/02/2018 5:56 AM, Michal Podhradsky wrote:
> Hi Kent,
>
> I did a fresh
>
> *repo init -u https://github.com/seL4/camkes-vm-manifest
> <https://github.com/seL4/camkes-vm-manifest> *
>
> so I am using the latest default.xml
>
> Now I can get a bit further - although still not all the way - here is the
> full output: https://gist.github.com/podhrmic/bc86178e60fad64ab870ff1fa19992
> e3
>
> and then the system as far as I can tell hangs - no serial or VGA output.
>
> What could be the cause?
>
> Regards
> M
>
> On Mon, Feb 19, 2018 at 4:07 PM, <Kent.Mcleod@data61.csiro.au> wrote:
>
>> Hi Michal,
>>
>>
>> Which revision of default.xml are you using?  Adrian thinks it could be
>> potentially related to, and fixed by, this commit[1] if you don't have it
>> yet.
>>
>>
>> Kent
>>
>>
>> [1] https://github.com/seL4/seL4/commit/3d6f4f9bb7bfe42628df
>> a555601401fa4efcdf2d​
>>
>>
>>
>> ------------------------------
>> *From:* Devel <devel-bounces@sel4.systems> on behalf of Michal Podhradsky
>> <mpodhradsky@galois.com>
>> *Sent:* Tuesday, February 20, 2018 9:37 AM
>> *To:* devel@sel4.systems
>> *Subject:* [seL4] CamkesVM CMA34CR_centos app
>>
>> Hi all,
>>
>> I have a CM34CR CPU module <https://wiki.sel4.systems/CMA34DBMC> and I am
>> trying to run the related camkes app on it.
>>
>> I choose the centos app: https://github.com/seL4/camkes
>> -vm/blob/master/apps/vm/cma34cr_centos.camkes
>>
>> I am using default camkes vm manifest from https://github.com/seL4/camkes
>> -vm-manifest.
>>
>> Compile with:
>>
>> *make clean *
>>
>> *make cma34cr_centos_defcondig *
>>
>> *make silentoldconfig *
>> *make*
>>
>> And then I create a bootable USB following instructions here
>> <https://wiki.sel4.systems/Hardware/IA32>.
>>
>> Then after I load the kernel and capdl image, I get the following output
>> on serial:
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>> *Boot config: parsing cmdline 'sel4kernel' Boot config: console_port =

>> 0x3f8 Boot config: debug_port = 0x3f8 Boot config: disable_iommu = false
>> Detected 1 boot module(s):   module #0: start=0xd34000 end=0x3b387e8
>> size=0x2e047e8 name='rootserver' Parsing GRUB physical memory map
>> Physical Memory Region from 0 size 9d400 type 1     Physical Memory Region
>> from 9d400 size 2c00 type 2     Physical Memory Region from e0000 size
>> 20000 type 2     Physical Memory Region from 100000 size 1ff00000 type 1
>> Adding physical memory region 0x100000-0x20000000     Physical Memory
>> Region from 20000000 size 200000 type 2     Physical Memory Region from
>> 20200000 size 1fe04000 type 1 Adding physical memory region
>> 0x20200000-0x40004000     Physical Memory Region from 40004000 size 1000
>> type 2     Physical Memory Region from 40005000 size 64bab000 type 1 Adding
>> physical memory region 0x40005000-0xa4bb0000     Physical Memory Region
>> from a4bb0000 size 1400000 type 2     Physical Memory Region from a5fb0000
>> size 4a0f000 type 1 Adding physical memory region 0xa5fb0000-0xaa9bf000
>> Physical Memory Region from aa9bf000 size 500000 type 2     Physical Memory
>> Region from aaebf000 size 100000 type 4     Physical Memory Region from
>> aafbf000 size 40000 type 3     Physical Memory Region from aafff000 size
>> 1000 type 1 Adding physical memory region 0xaafff000-0xab000000
>> Physical Memory Region from ab000000 size 4a00000 type 2     Physical
>> Memory Region from f0000000 size 4000000 type 2     Physical Memory Region
>> from feb00000 size 4000 type 2     Physical Memory Region from fec00000
>> size 1000 type 2     Physical Memory Region from fed10000 size a000 type 2
>>      Physical Memory Region from fed1c000 size 4000 type 2     Physical
>> Memory Region from fee00000 size 1000 type 2     Physical Memory Region
>> from ffc00000 size 400000 type 2     Physical Memory Region from 100000000
>> size 14f600000 type 1 Adding physical memory region 0x100000000-0x24f600000
>> Got VBE info in multiboot. Current video mode is 16767 ACPI: RSDP
>> paddr=0xfe020 ACPI: RSDP vaddr=0xfe020 ACPI: RSDT paddr=0xaafda0c4 ACPI:
>> RSDT vaddr=0xaafda0c4 Kernel loaded to: start=0x100000 end=0xc17000
>> size=0xb17000 entry=0x101269 ACPI: RSDT paddr=0xaafda0c4 ACPI: RSDT
>> vaddr=0xaafda0c4 ACPI: FADT paddr=0xaaffb000 ACPI: FADT vaddr=0xaaffb000
>> ACPI: FADT flags=0x3c6a5 ACPI: DMAR paddr=0xaafde000 ACPI: DMAR
>> vaddr=0xaafde000 ACPI: IOMMU host address width: 36     ACPI: registering
>> RMRR entry for region for device: bus=0x0 dev=0x1d fun=0x0     ACPI:
>> registering RMRR entry for region for device: bus=0x0 dev=0x1a fun=0x0
>> ACPI: registering RMRR entry for region for device: bus=0x0 dev=0x14
>> fun=0x0     ACPI: registering RMRR entry for region for device: bus=0x0
>> dev=0x2 fun=0x0 ACPI: 2 IOMMUs detected ACPI: MADT paddr=0xaaff9000 ACPI:
>> MADT vaddr=0xaaff9000 ACPI: MADT apic_addr=0xfee00000 ACPI: MADT flags=0x1
>> ACPI: MADT_APIC apic_id=0x0 ACPI: MADT_APIC apic_id=0x1 ACPI: MADT_APIC
>> apic_id=0x2 ACPI: Not recording this APIC, only support 2 ACPI: MADT_APIC
>> apic_id=0x3 ACPI: Not recording this APIC, only support 2 ACPI: MADT_IOAPIC
>> ioapic_id=0 ioapic_addr=0xfec00000 gsib=0 ACPI: MADT_ISO bus=0 source=0
>> gsi=2 flags=0x0 ACPI: MADT_ISO bus=0 source=9 gsi=9 flags=0xd ACPI: 2
>> CPU(s) detected ELF-loading userland images from boot modules:
>> size=0x41fc000 v_entry=0x409000 v_start=0x400000 v_end=0x45fc000
>> p_start=0x3b39000 p_end=0x7d35000 Moving loaded userland images to final
>> location: from=0x3b39000 to=0xc17000 size=0x41fc000 Starting node #0 with
>> APIC ID 0 Mapping kernel window is done ========== KERNEL EXCEPTION
>> ========== Vector:  0xd ErrCode: 0x0 IP:      0xffffffff80115c04 SP:
>> 0xffffffff80a0bfa0 FLAGS:   0x10046 CR0:     0x80010013 CR2:     0x0
>> (page-fault address) CR3:     0xa12000 (page-directory physical address)
>> CR4:     0x110668 Stack Dump: *0xffffffff80a0bfa0 == 0x0
>> *0xffffffff80a0bfa8 == 0x0 *0xffffffff80a0bfb0 == 0x3b39000
>> *0xffffffff80a0bfb8 == 0xffffffff80116b80 *0xffffffff80a0bfc0 == 0x0
>> *0xffffffff80a0bfc8 == 0x22a8 *0xffffffff80a0bfd0 == 0x0
>> *0xffffffff80a0bfd8 == 0x0 *0xffffffff80a0bfe0 == 0xffffffff80000000
>> *0xffffffff80a0bfe8 == 0x7e000 *0xffffffff80a0bff0 == 0xaa24c70c
>> *0xffffffff80a0bff8 == 0x1f *0xffffffff80a0c000 == 0xfffffffff000ba86
>> *0xffffffff80a0c008 == 0xffffffff8081f0c0 *0xffffffff80a0c010 == 0x0
>> *0xffffffff80a0c018 == 0x0 *0xffffffff80a0c020 == 0x0 *0xffffffff80a0c028
>> == 0x0 *0xffffffff80a0c030 == 0x0 *0xffffffff80a0c038 == 0x0 Halting...

>> halting... Kernel entry via Interrupt, irq 0 *
>>
>> Any pointers at what is the cause of error here? The machien runs normally
>> with vanilla CentOS so I don't think it is a hardware issue. Also, I am
>> assuming the CMA34CR is identical to the one you have on your side (at
>> least checking the lspci output against the camkes description the memory
>> regions etc seem to match).
>>
>> Thanks in advance.
>> M
>>
>
>
>
> _______________________________________________
> Devel mailing list
> Devel@sel4.systems
> https://sel4.systems/lists/listinfo/devel
>