Re: [seL4] Problem booting camkes arm vmm on TK1 from SD Card

Hi Mike, Could you run "file images/capdl-loader-image-arm-tk1"? If you see "images/capdl-loader-image-arm-tk1: MS-DOS executable", the image is an EFI image, so bootefi command should help. Also, the link, https://docs.sel4.systems/Hardware/jetsontk1.html, may be helpful. Regards, Yanyan On Fri, 2020-01-24 at 15:24 -0500, Mike Clark wrote:

Chris,

Looks like I might have spoken too soon. When I use go instead of bootelf, the board actually resets. Here are the log messages:

Tegra124 (Jetson TK1) # fatload mmc 1 0x82000000 capdl-loader-image- arm-tk1 20435184 bytes read in 964 ms (20.2 MiB/s) Tegra124 (Jetson TK1) # go 0x82000000 ## Starting application at 0x82000000 ... data abort pc : [<82000110>] lr : [<fff51d84>] reloc pc : [<021c3110>] lr : [<80114d84>] sp : fd7f8610 ip : 00000002 fp : fff6be40 r10: 00000002 r9 : fd7ffed0 r8 : fffcbe9c r7 : fda60420 r6 : 82000000 r5 : 00000001 r4 : 00000000 r3 : 82000000 r2 : fda60424 r1 : fda60424 r0 : 00006090 Flags: nzCv IRQs off FIQs off Mode SVC_32 Code: 00000000 00000000 00000000 42100040 (7865742e) Resetting CPU ...

resetting ...

U-Boot SPL 2020.01-00442-gc00bd81ae0 (Jan 10 2020 - 11:10:18 -0500) Trying to boot from RAM

U-Boot 2020.01-00442-gc00bd81ae0 (Jan 10 2020 - 11:10:18 -0500)

SoC: tegra124 Reset cause: SW_MAIN Model: NVIDIA Jetson TK1 Board: NVIDIA Jetson TK1 DRAM: 2 GiB MMC: sdhci@700b0400: 1, sdhci@700b0600: 0 Loading Environment from MMC... OK In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 Tegra124 (Jetson TK1) #

Doing readelf on the image that is being built doesn't work either

$ readelf -h capdl-loader-image-arm-tk1 readelf: Error: Not an ELF file - it has the wrong magic bytes at the start

My old images from a year ago still boot just fine with bootelf. Any thoughts?

Mike

On Fri, Jan 10, 2020 at 3:46 PM Mike Clark wrote:

...

That did the trick Chris. Thanks!

On Fri, Jan 10, 2020 at 3:30 PM Chris Guikema < Chris.Guikema@dornerworks.com> wrote:

...

Mike,

Can you do a readelf of your outputted image to make sure its not compiling as a binary? If it is, you’ll have to use the “go” command in u-boot instead.

Thanks,

Chris Guikema

DornerWorks

From: Devel On Behalf Of Mike Clark Sent: Friday, January 10, 2020 3:22 PM To: devel@sel4.systems Subject: [seL4] Problem booting camkes arm vmm on TK1 from SD Card

CAUTION: This email originated from outside the organization. Do not click links or open attachments unless you recognize the sender and know the content is safe. I'm using the docker image to build the CAmkES ARM VMM project using roughly the instructions here: https://docs.sel4.systems/VM/CAmkESARMVM.html (they are slightly out of date).

I do:

../init-build.sh -DAARCH32=TRUE -DCAMKES_VM_APP=vm_minimal -DPLATFORM=tk1

ninja

Then I copy the resulting image from the images directory to an SD card and put that in my TK1.

When U-Boot starts I use the following commands to try to boot

fatload mmc 1 0x10000000 capdl-loader-image-arm-tk1

bootelf 0x10000000

To which I get an error: No elf image at address 0x10000000

I tried with an older version of U-Boot (that worked following this same procedure about a year ago). It is U-Boot SPL 2014.10- rc2-g3127911 (Jun 07 2016 - 21:00:01)

I also tried updating U-Boot to U-Boot SPL 2020.01-00442- gc00bd81ae0 (Jan 10 2020 - 11:10:18 -0500). Same error.

Any thoughts or suggestions on how I get this to boot?

_______________________________________________ Devel mailing list Devel@sel4.systems https://sel4.systems/lists/listinfo/devel