May 2021 - Devel - lists.sel4.systems

seL4 test on x86
by Yevgeny Lavrov 29 Jan '25

29 Jan '25

Hello, I'm new to seL4 and I'm just doing it for learning purpose. I'm trying to run seL4 test suite or simple hello world task from seL4 tutorials on the real hardware. So far I had no problems compiling seL4 test suite and running via QEMU for both x32 and x64 platforms. However, when I try to run it on the actual hardware following Running on real hardware tutorial for x86 I end up with no output at all and no error msgs that can give me a clue on where something went wrong. After compiling seL4test for x86, I ended up with two images in sel4_dir/images/ folder. Copied them over to /boot/sel4/ folder and created a new GRUB2 entry that looks like this menuentry “seL4 test suite” --class os { load video insmod gzio insmod part_msdos insmod ext2 set root=’(hd0,msdos5)’ multiboot /boot/sel4/kernel-ia32-pc99 module /boot/sel4/sel4test-driver-image-ia32-pc99 } update grub, restart and select the new entry from GRUB menu. I end up with blinking cursor on the top-left side of the screen. Please advise.

4 3

Stuck during invalidate local TLB in Tx2
by Muneeswaran Rajendran 15 Oct '24

15 Oct '24

Hi seL4 Dev team, Can someone explain the reason (share the reference) to invalidate the local TLB during kernel vspace activation as part CPU initialisation. The Tx2 board stuck while performing this operation. As per my understanding both Tx1 and Tx2 are using same A57 core. so the TLB initialisation and invalidation remain same for Tx2 and should not stuck during invalidation.Please correct me if anything wrong here. I understand from that instruction (tlbi vmalle1) which is invalidating stage 1 entries associated to the current VMID. Also from arm mmu code the seL4 setting up (TCR_EL1) TCR register addressing space as 48bit, ASID as 16bit and page table setup 4k granular size. I am using MRS macro to dump the spsr_el1 and dspsr_el0 register to see the state of processor but its throwing synchronous exception. Do we have any other option to dump all the register content to see the state of processor like we have one in 'sel4debug_dump_registers' which is used in sel4test code. Regards, Muneeswaran R

3 4

Questions about Memory Management in seL4
by Daniel Wang 18 May '23

18 May '23

Hi all, Sorry to bother, I have some basic questions about seL4 memory management. Can someone help me? 1. where is the kernel’s address space? I know there are basically three methods: a) separate virtual address space, e.g. through changing page tables on entry into privileged mode to access b) physical space, e.g. through disable automatic hardware translation of virtual addresses on entry into privilege mode c) privilege region in each process’s virtual address space, e.g. through page table to map kernel address into use-mode process. My question is which of this is being used by seL4 microkernel? 2. Objects like CSpace, VSpace, CNode, TCB, Endpoint, etc. are called kernel objects, but it seems all dynamically allocated in thread running/creating time. Are those objects (e.g. Figure 3.3 in seL4 manual) in kernel space or in user space? 3. I read that after the kernel boot up, it passes all resources, untyped memory to the first thread. Are those untyped memory physical memory or virtual memory in a single page? The reason I ask is I’m learning the code of the UNSW AOS project (two of the assignment projects are implementing frame and papers). I’m confused that before the implementation of frames and pages what kind of memory is passed to the the first thread? I saw int AOS project, it uses ut_table_init(), ut_steal_mem(), I wonder what kind of memory it operates on? Thanks -Dan

5 4

gic v2 vs gic v3
by Chris Koziarz 09 Jul '21

09 Jul '21

Hi all, I'm trying to port camkes-arm-vm to a different platform, that supports gic-v3 In the process, I hit a compilation error: Building C object kernel/CMakeFiles/kernel_all_pp_...rapper_temp_lib.dir/ kernel_all_pp_prune_wrapper_temp.c.obj FAILED: kernel/kernel_all_pp_prune_wrapper_temp.c In file included from /home/chris/camkes-tqma8xqp- vm/kernel/src/arch/arm/object/vcpu.c:15: /home/chris/camkes-tqma8xqp-vm/kernel/include/arch/arm/arch/machine/gic_v2.h:23: error: "IRQ_MASK" redefined [-Werror] 23 #define IRQ_MASK MASK(10u) In file included from kernel/gen_headers/plat/platform_gen.h:23, from /home/chris/camkes-tqma8xqp-vm/kernel/include/plat/ default/plat/machine.h:8, from /home/chris/camkes-tqma8xqp- vm/kernel/include/machine.h:9, from /home/chris/camkes-tqma8xqp- vm/kernel/include/api/syscall.h:10, from /home/chris/camkes-tqma8xqp- vm/kernel/src/api/faults.c:10: /home/chris/camkes-tqma8xqp-vm/kernel/include/arch/arm/arch/machine/gic_v3.h:30: note: this is the location of the previous definition 30 #define IRQ_MASK MASK(16u) which is an indicative that both gic_v3.h & gic_v2.h headers have been included, which is an error because said headers are not compatible: kernel/include/arch/arm/arch/machine/gic_v3.h:#define IRQ_MASK MASK(16u) kernel/include/arch/arm/arch/machine/gic_v2.h:#define IRQ_MASK MASK(10u) So my question is: how can I configure the build to avoid such a conflict? I can grepp the relevant configuration option in CMakeCache.txt: build_tqma8/CMakeCache.txt:CONFIGURE_INTERRUPT_CONTROLLER:INTERNAL=arch/machine/gic_v3.h but cannot see it in ccmake gui because it's "INTERNAL" What is the solution? - replace this option somehow to use gic_v2 and have my HW use gic v.2, or - change compilation options to use gic_v3 everywhere Thanks for any help, Chris.

4 5

hello_rumprun app not worked
by MOHAMAD REZA SHAFIEI 13 Jun '21

13 Jun '21

hi. i'm recently worked on sel4 with camkes framework. when i compile rumprun_hello on x86_64 platform its compiled and build correctly but when run with qemu by ./simulate script, program crashed with this errors: simple_get_extended_bootinfo_length@simple.h:600 simple_get_extended_bootinfo_length not implemented FAULT HANDLER: data fault from hello.hello_0_control (ID 0x1) on address 0x8, pc = 0x402b7f, fsr = 0x6 FAULT HANDLER: Register dump: FAULT HANDLER: rip :0x402b7f , . . so i found that this method not implemented yet so i return 0 in this method and resolved. for second problem that cause failure if trace program and i found that in "init rumprun" process the program failed in the /projects/sel4runtime/include/sel4_arch/x86_64/sel4runtime/thread_arch.h file and sel4runtime_set_tls_base method. so i read git log and in recently commit your team use sel4runtime for thread TLS, so when we run rumprun_hello, the program failed in sel4runtime_set_tls_base method. can you help me fix this bug? thanks for your attention. -- This email was Anti Virus checked by Security Gateway.

4 4

MMC wait after second command in intialization with mmc_init
by MOHAMAD REZA SHAFIEI 13 Jun '21

13 Jun '21

hi there . i'm work on mmc storage with sel4. i wrote a simple app that use mmc an here is that : ////////////////////////////////////////////////////////////////////// static int count = 0; ps_io_ops_t io_ops = {0}; struct netif* net_if; mmc_card_t mmc_card = 0; sdio_host_dev_t sdio_host_dev; int mmc_found = 0; void mmc_irq_handle(ps_irq_t* irq) { printf("mmc irq handle .... \n"); if(!mmc_found){ mmc_irq_acknowledge(irq); // printf("mmc not found yet :)\n"); sdio_host_dev.handle_irq(&sdio_host_dev,irq->irq.number); return ; } mmc_irq_acknowledge(irq); mmc_handle_irq(mmc_card,irq->irq.number); } int run(void) { notification = timer_notification(); int err = camkes_io_ops(&io_ops); if (err != 0) { ZF_LOGF("Can not init ops : %d\n", err); }; printf("initialize sdhc1 ...\n"); err = sdio_init(SDHC1, &io_ops, &sdio_host_dev); // while card not present check while(sdio_host_dev.reset(&sdio_host_dev) == -1){ delay(1000); } printf("before mmc_init\n"); mmc_init(&sdio_host_dev, &io_ops, &mmc_card); mmc_found = 1; printf("after mmc_init\n"); if (!err) { printf("SDHC1 inited successfully.\n"); } else { printf("SDHC1 initizatino failed!: %d", err); } while (true) { printf(".\n"); delay(1000); } return 0; //////////////////////////////////////////////// its work but in mmc_init after going to mmc_reset , first command sent but in second command (ie MMC_SEND_EXT_CSD ) wait for ever... can any body help me? best regards -- This email was Anti Virus checked by Security Gateway.

2 1

Camkes-vm-linux on
by Hugo V.C. 11 Jun '21

11 Jun '21

Hi, I'm trying the camkes-vm-linux tutorial and can't run it in qemu despite having nested guests enabled: hugo@dev:~/seL4/sel4-tutorials-manifest/camkes-vm-linux_build$ cat /sys/module/kvm_intel/parameters/nested Y --------- hugo@dev:~/seL4/sel4-tutorials-manifest/camkes-vm-linux_build$ sudo ./simulate --machine q35,accel=kvm,kernel-irqchip=split --mem-size 2G --extra-cpu-opts "+vmx" --extra-qemu-args="-enable-kvm -device intel-iommu,intremap=off -net nic,model=e1000 -net tap,script=no,ifname=tap0" ./simulate: qemu-system-x86_64 -machine q35,accel=kvm,kernel-irqchip=split -cpu Nehalem,+vme,+pdpe1gb,-xsave,-xsaveopt,-xsavec,-fsgsbase,-invpcid,+syscall,+lm,enforce,+vmx -nographic -serial mon:stdio -m size=2G -enable-kvm -device intel-iommu,intremap=off -net nic,model=e1000 -net tap,script=no,ifname=tap0 -kernel images/kernel-x86_64-pc99 -initrd images/capdl-loader-image-x86_64-pc99 qemu-system-x86_64: warning: host doesn't support requested feature: CPUID.80000001H:EDX.pdpe1gb [bit 26] qemu-system-x86_64: warning: host doesn't support requested feature: MSR(48FH).vmx-exit-load-perf-global-ctrl [bit 12] qemu-system-x86_64: warning: host doesn't support requested feature: MSR(490H).vmx-entry-load-perf-global-ctrl [bit 13] qemu-system-x86_64: Host doesn't support requested features ./simulate: QEMU failed; resetting terminal in 5 seconds--interrupt to abort --------- any tutorial to build/boot it natively on x86_64? Thanks,

2 1

Bug when compling in release mode
by Ben Fiedler 08 Jun '21

08 Jun '21

Hello everyone, I've recently found an interesting bug that only occurs when compiling in release mode. Use of the ZF_LOG library (for normal log output) leads to syscalls being made when the capdl-loader runs. These are invoked via musllibc's __stdio_write, which relies on __sysinfo being set correctly for syscalls to work. When compiling with RELEASE=OFF this works fine, however when compiling with RELEASE=ON, __sysinfo is not set (yet?), and subsequently leads to an illegal prefetch exception when __stdio_write tries to invoke a syscall. Setting __sysinfo to sel4_vsyscall using gdb during runtime fixes this. I don't really know the correct place to fix this in the code, but I hope that you can provide some hints on where to fix this bug. Thanks a lot for your help! Cheers, Ben

2 2

libsel4utils: load_segment memory leak bug
by wzt wzt 04 Jun '21

04 Jun '21

hello: i found a bug memory leak bug in libsel4utils/src/elf.c static int load_segment(vspace_t *loadee_vspace, vspace_t *loader_vspace, vka_t *loadee_vka, vka_t *loader_vka, const char *src, size_t file_size, int num_regions, sel4utils_elf_region_t regions[num_regions], int region_index) { seL4_CPtr loader_slot; cspacepath_t loader_frame_cap; error = vka_cspace_alloc(loader_vka, &loader_slot); [1] while (pos < segment_size && error == seL4_NoError) { reservation_t reservation; if (loadee_vaddr < region.reservation_vstart) { if ((region_index - 1) < 0) { ZF_LOGE("Invalid regions: bad elf file."); return 1; [2] } } if [2] happned, it not free the prev alloc memory, and then it's memory will be leaked. i think the correct way is invoke vka_cspace_free() before return.

3 2

Pass Ethernet device to CAmkES ARM VM when using QEMU
by Olof Holmberg 02 Jun '21

02 Jun '21

Hi, I am currently trying to pass a device for ethernet access through qemu to the vm. However there seems to be some issue since the device is not passed through correctly. I have looked at some resources for guidance on how to solve it: https://github.com/seL4/sel4webserver (webserver example) https://lists.sel4.systems/hyperkitty/list/devel@sel4.systems/message/X34TX… (old devel thread) And the important parts for this to work seems to be untyped_mmios for the vm (in devices.camkes for qemu-arm-virt): vm0.untyped_mmios = [ "0x8040000:12", // Interrupt Controller Virtual CPU interface (Virtual Machine view) /* TODO: QEMU PCI addresses could change - ideally need to decode from pcie node */ "0x10040000:17", // QEMU PCI MMIO "0x3eff0000:16", // QEMU PCI IO ports "0x40000000:29", // Linux kernel memory regions ]; And passing the device to QEMU in the simulation script: $ sudo ./simulate --extra-qemu-args="-netdev tap,id=mynet0,ifname=tap0,script=no,downscript=no -device virtio-net,netdev=mynet0,mac=52:55:00:d1:55:01" However when listing the devices with "ip a" on the VM it does not show an eth0 device: # ip a 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue qlen 1 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: tunl0@NONE: <NOARP> mtu 1480 qdisc noop qlen 1 link/ipip 0.0.0.0 brd 0.0.0.0 3: ip6tnl0@NONE: <NOARP> mtu 1452 qdisc noop qlen 1 link/tunnel6 00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00 brd 00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00 But on the host the device that is passed to qemu can be seen: $ ip link show tap0 6: tap0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000 link/ether 62:43:43:54:2d:e6 brd ff:ff:ff:ff:ff:ff I am not sure if I missed something or if it is the QEMU addresses for the pci region that are not correct. Is there any output during boot or build that could give insight in what went wrong when it tries to passthrough the device? Also are there are any resources or guidelines on how to decode the pcie node? (Since I assume this has to be done inside the vm with the limited selection of commands available). Best regards, Olof

1 1